[vz-users] GPIO Zuordnung - s0vz.cfg?

[Peter Haider]

#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

# Print the IP address
_IP=$(hostname -I) || true
if [ "$_IP" ]; then
  printf "My IP address is %s\n" "$_IP"
fi

# Part of DS2482 I2C 1-Wire Master to Volkszaehler 'RaspberryPI deamon'.
echo ds2482 0x18 > /sys/bus/i2c/devices/i2c-1/new_device
# echo ds2482 0x19 > /sys/bus/i2c/devices/i2c-1/new_device
# echo ds2482 0x1a > /sys/bus/i2c/devices/i2c-1/new_device

# Register I2C RTC
# echo ds1307 0x68 > /sys/bus/i2c/devices/i2c-1/new_device

# Part of S0/Impulse to Volkszaehler 'RaspberryPI deamon','s0vz'
echo 17 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio17/edge
echo 18 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio18/edge
echo 22 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio22/edge
echo 23 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio23/edge
echo 24 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio24/edge
echo 27 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio27/edge

# Part of S0/Impulse to Volkszaehler 'RaspberryPI deamon','s0vz_new'
# echo 4 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio4/edge
# echo 18 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio18/edge
# echo 17 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio17/edge
# echo 23 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio23/edge
# echo 27 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio27/edge
# echo 22 > /sys/class/gpio/export && echo "rising" >
/sys/class/gpio/gpio22/edge

# GPIOs exportieren und Datenrichtung einstellen, 'Schaltausgang_new'
# echo 24 > /sys/class/gpio/export
# echo 25 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio24/direction
# echo out > /sys/class/gpio/gpio25/direction

# GPIOs exportieren und Datenrichtung einstellen, 'Schaltausgang'
echo 9 > /sys/class/gpio/export
echo 11 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio9/direction
echo out > /sys/class/gpio/gpio11/direction


sudo 1wirevz

sudo s0vz

# sudo s0vz_new

stty -F /dev/ttyUSB0 300 -parity -cstopb
sudo vzlogger -p 

exit 0




-----Ursprüngliche Nachricht-----
Von: volkszaehler-users
[mailto:volkszaehler-users-bounces at demo.volkszaehler.org] Im Auftrag von
Udo1
Gesendet: Dienstag, 09. Dezember 2014 20:50
An: volkszaehler-users at demo.volkszaehler.org
Betreff: Re: [vz-users] GPIO Zuordnung - s0vz.cfg?

Hallo Peter,

Am 09.12.2014 15:30, schrieb Peter Haider:
> ich verwende das neueste Image für den Rasperry Pi B+ 
zeig mal deine /etc/rc.local

Gruß
Udo