[vz-users] /dev/bus/w1 plötzlich weg, wie geht die Fehlereingrenzung?

[Bernd Gewehr]

Hallo!

Habe ein Pi 2B mit Udos Erweiterung seit langer Zeit.

2 S0 Zähler, ein SML Zähler und einige w1therm Sensoren machten ihren Job.

Nun auf neue Disk gecloned, wieder abgeschmissen, nichts geht mehr.

Innodb table defekt habe ich hinbekommen. Middleware und frontend laufen, bekommen aber keine neuen Daten.

Vzlogger startprotokoll:
root at volkszaehler:/var/www/volkszaehler.org/lib/Definition# sudo service vzlogger restart
[....] Restarting smartmetering server: vzloggerp11-kit: invalid config filename, will be ignored in the future: /etc/pkcs11/modules/gnome-keyring-module
[Jun 05 13:18:41][main] vzlogger v0.5.2 based on heads/master-0-gf72dbc5ba5 from Fri, 26 Feb 2016 21:56:39 -0300 started.
[Jun 05 13:18:41][mtr0] Creating new meter with protocol sml.
[Jun 05 13:18:41][mtr0] Meter configured, enabled.
[Jun 05 13:18:41]       New meter initialized (protocol=sml)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn0] New channel initialized (uuid=...28f8bf api=volkszaehler id=1-0:1.7.1)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn1] New channel initialized (uuid=...7a3a7f api=volkszaehler id=1-0:1.8.1)
[Jun 05 13:18:41][mtr1] Creating new meter with protocol s0.
[Jun 05 13:18:41][s0]   unknown option for mmap (). Falling back to normal gpio.
[Jun 05 13:18:41][mtr1] Meter configured, enabled.
[Jun 05 13:18:41]       New meter initialized (protocol=s0)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn2] New channel initialized (uuid=...a80770 api=volkszaehler id=Impulse)
[Jun 05 13:18:41][mtr2] Creating new meter with protocol s0.
[Jun 05 13:18:41][s0]   unknown option for mmap (). Falling back to normal gpio.
[Jun 05 13:18:41][mtr2] Meter configured, enabled.
[Jun 05 13:18:41]       New meter initialized (protocol=s0)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn3] New channel initialized (uuid=...888ef4 api=volkszaehler id=Impulse)
[Jun 05 13:18:41][mtr3] Creating new meter with protocol w1therm.
[Jun 05 13:18:41][mtr3] Meter configured, enabled.
[Jun 05 13:18:41]       New meter initialized (protocol=w1therm)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn4] New channel initialized (uuid=...acca61 api=volkszaehler id=28-000004858252)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn5] New channel initialized (uuid=...67b0d0 api=volkszaehler id=28-000004854a62)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn6] New channel initialized (uuid=...bff0dc api=volkszaehler id=28-0000048553f3)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn7] New channel initialized (uuid=...aff99d api=volkszaehler id=28-00000484d527)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn8] New channel initialized (uuid=...7465a4 api=volkszaehler id=28-000004851d7e)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn9] New channel initialized (uuid=...27a1f8 api=volkszaehler id=28-00000484c3e1)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn10]New channel initialized (uuid=...5a40c6 api=volkszaehler id=28-000004857e63)
[Jun 05 13:18:41]       Configure channel.
[Jun 05 13:18:41][chn11]New channel initialized (uuid=...d8f760 api=volkszaehler id=28-000004856747)
[Jun 05 13:18:41]       Have 4 meters.
[Jun 05 13:18:41][main] log level is 10
[Jun 05 13:18:41][main] daemon=1, local=0
[Jun 05 13:18:41]       Daemonize process...
. ok

Vzlogger.log:
[Jun 05 13:26:00]       Opened logfile /var/log/vzlogger.log
[Jun 05 13:26:00][push] No pushDataServer defined.
[Jun 05 13:26:00][]     ===> Start meters
[Jun 05 13:26:00][mtr0] Meter connection established
[Jun 05 13:26:00][mtr0] Meter thread started
[Jun 05 13:26:00][mtr0] Meter is opened. Starting channels.
[Jun 05 13:26:00][chn0] Logging thread started
[Jun 05 13:26:00][chn1] Logging thread started
[Jun 05 13:26:00][mtr0] Number of readers: 32
[Jun 05 13:26:00][mtr0] Config.daemon: 1
[Jun 05 13:26:00][mtr0] Config.local: 0
[Jun 05 13:26:00][chn0] Start logging thread for volkszaehler-api. Running as daemon: yes
[Jun 05 13:26:00][chn0] Using default volkszaehler api.
[Jun 05 13:26:00][chn1] Start logging thread for volkszaehler-api. Running as daemon: yes
[Jun 05 13:26:00][chn1] Using default volkszaehler api.
[Jun 05 13:26:00][s0]   counter_thread created
[Jun 05 13:26:00][mtr1] Meter connection established
[Jun 05 13:26:00][mtr1] Meter thread started
[Jun 05 13:26:00][mtr1] Meter is opened. Starting channels.
[Jun 05 13:26:00][chn2] Logging thread started
[Jun 05 13:26:00][s0]   counter_thread created
[Jun 05 13:26:00][mtr2] Meter connection established
[Jun 05 13:26:00][mtr2] Meter thread started
[Jun 05 13:26:00][mtr2] Meter is opened. Starting channels.
[Jun 05 13:26:00][chn3] Logging thread started
[Jun 05 13:26:00][s0]   Counter thread started with blocking hwif
[Jun 05 13:26:00][mtr1] Number of readers: 4
[Jun 05 13:26:00][mtr1] Config.daemon: 1
[Jun 05 13:26:00][mtr1] Config.local: 0
[Jun 05 13:26:00][chn2] Start logging thread for volkszaehler-api. Running as daemon: yes
[Jun 05 13:26:00][chn2] Using default volkszaehler api.
[Jun 05 13:26:00][s0]   Counter thread started with blocking hwif
[Jun 05 13:26:00][mtr2] Number of readers: 4
[Jun 05 13:26:00][mtr2] Config.daemon: 1
[Jun 05 13:26:00][mtr2] Config.local: 0
[Jun 05 13:26:00][chn3] Start logging thread for volkszaehler-api. Running as daemon: yes
[Jun 05 13:26:00][chn3] Using default volkszaehler api.
[Jun 05 13:26:00][w1t]  scanW1devices failed!
[Jun 05 13:26:00][mtr3] Cannot open meter
[Jun 05 13:26:00][]     Startup failed: Meter open failed.

Keine Daten im Frontend, keine neuen Daten in der Db.

I2C und SPI sind aktivert.

Wo soll ich ansetzen?

Danke und Gruß
Bernd

Gesendet von Mail für Windows 10

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://demo.volkszaehler.org/pipermail/volkszaehler-users/attachments/20160605/e44d19d4/attachment.html>